TilingPlastering and renderingFloor levelingFinishingPrimersOther adhesivesWaterproofing and repairingTile GroutsUnmodified mixes
rus  |  eng
 

Base preparation

   The base surface should be strong, carefully cleared of dust, dirt, oils, and greases. Unstable and fragile parts of the base must be removed. Large unevenness of a walls, a crack, and a recess should be pre-aligned with one of the Plasters IVSIL. To correct uneven floors use one of self-leveling floors or screeds IVSIL TIE-ROD. Small irregularities of walls and floors (depth of 5mm) may be aligned using tile adhesive IVSIL START. 

   Before the faceworking surface should be primed with IVSIL BAZOVAYA. Strongly absorbing bases (gaze and foam concrete, gipsum plaster, anhydrite floor) should be primed with IVSIL GLUBOKOGO PRONIKNOVENIYA (primer penetrator).

Mixing of mortar

   Dry mix is poured into a mixing bucket with clean water in the following proportion: 1 kg of dry mix for 0,21-0,23 l of water. Then it is thoroughly stirred, manually or with a mixing drill, until the mixture is homogeneous and elastic. The received mixture is left for 5 minutes and then stirred again. Prolonged period of this tile adhesive setting allows this mixture to be used within 4 hours.

Application

   Adhesive solution is applied on basis with the help of a trowel and then is spread with a notched trowel. The size of notches depends on the size of a tile. Put a tile on the top of the mixture, which has just been applied, and press it to the surface. After being pressed, adhesive mixture should be covering not less than 65% of the tile’s surface, for tiles 20*20 sm and bigger - 80%. When used for exterior jobs, to provide 100% of tile’s cover with adhesive and to guarantee gluing to the surface, it is recommended to apply adhesive to the reverse side of the tile as well before to put it on the surface covered with the mixture.

   A tile must be laid within 10 minute from application of adhesive on the basis. Correction of the tile position can be done within 10 minutes after the tile is laid. There is no need to soak tiles in water before use. The air temperature and the temperature of the basis must be from +5ªC to +30ªC.

   Grouting of wall tiles can be done in 6-8 hours, grouting of floor tiles in 24 hours. In bad conditions (strong wind, direct sunshine, high or low temperature, highly absorbing surface) lifetime of the prepared mixture may be decreased. All technical characteristics of the adhesive are fully active at the temperature of 18-20ªC and 60% humidity level.

 
Consultation on the pplication materials

START

  

   Multipurpose tile adhesive IVSIL START is suitable for floor tilling jobs and wall tilling jobs, specifically for walls with mineral stable basis (cement and gypsum plasters, concrete, brick walls, gypsum, cement and anhydrite floors, and stable, fixed plasterboards). It is used for ceramic and porcelain tiles, ceramic mosaic, artificial, light, interior, decorative stone.   

    IVSIL Start is used as tile adhesive for exterior work and interior work (for example heated/unheated, humid premises). It is suitable for all types of accommodation premises, for bathrooms, kitchens, corridors, terraces, balconies, basements, offices and other premises. It can be also used for fixing of small (up to 5 mm) uneven patches of basis prior to tiling of floors and walls.

   It is a reliable adhesive, which can stick tiles on vertical surfaces and stop them from sliding down. IVSIL Start allows to lay tiles from top to bottom. The basic wholesale price of frost resistant tile adhesive IVSIL START in Moscow is 165 roubles. To see prices of other IVSIL tile adhesives, please visit our «Price List» section.    

See also: adhesive for thick-layered tilling and standard ceramic-granite IVSIL MAXI PLUS, IVSIL BAZOVAYA primer for exterior jobs or go to all IVSIL Tile adhesives.

   Multipurpose tile adhesive, water resistant and frost resistant adhesive for tiles IVSIL START.

 
 

Technical characteristics

Mixing proportion: 1l of water
On 1 kg of a mix0,21 0,23
On 25 kg of a mix5,25 5,75
The consumption at a thickness of a layer of 1 mm, on 1 sq. m1,4 1,6kg
Thickness of a layer of a solution, mm2-6mm
Viability of a solution4 hours
Open operating time15 min
Updating time10 min
Hardening time24 hours
Temperature of works and the baseFrom +5 to +30
Durability on compression10 MPa
Adhesive strength0,5 MPa
Frost resistance35 cycles
Packaging25 kg bag
 
Packaging and storage
Adhesive mix START is delivered in 25kg Kraft-bags. A storage warranty period in a dry premise in packaging materials of the manufacturer 12 months
The consumption
Average consumption 1,4 1,6 kg of a dry mix on 1 m. of a sq. surface at a thickness of a layer 1 mm. Practically the expense depends on degree of flatness of the base, size of a teeth and a sort of an applied tile.
 
Home Search and map
Rambler's Top100
Site development —
the Internet-agency «Webstroy»