TilingPlastering and renderingFloor levelingFinishingPrimersOther adhesivesWaterproofing and repairingTile GroutsUnmodified mixes
rus  |  eng
 

Base preparation

   The base surface should be strong, carefully cleared of dust, dirt, oils, and greases. Unstable and fragile parts of the base must be removed. Unevenness of a walls and floors (depth of 20mm) may be aligned using tile adhesive IVSIL MAXI PLUS.

   Before the faceworking surface should be primed with IVSIL BAZOVAYA. Strongly absorbing bases (gaze and foam concrete, gipsum plaster, anhydrite floor) should be primed with IVSIL GLUBOKOGO PRONIKNOVENIYA (primer penetrator).

Mixing of mortar

   Dry mix is poured into a mixing bucket with clean water in the following proportion: 1 kg of dry mix for 0,19-0,21 l of water. Then it is thoroughly stirred, manually or with a mixing drill, until the mixture is homogeneous and elastic. The received mixture is left for 5 minutes and then stirred again. Prolonged period of this tile adhesive setting allows this mixture to be used within 3 - 4 hours.

Application

   Adhesive solution is applied on basis with the help of a trowel and then is spread with a notched trowel. The size of notches depends on the size of a tile. Put a tile on the top of the mixture, which has just been applied, and press it to the surface. After being pressed, adhesive mixture should be covering not less than 65% of the tile’s surface, for ceramic tiles 20*20 and bigger and for all size ceramic-granite - 80%. When used for exterior jobs, to provide 100% of tile’s cover with adhesive and to guarantee gluing to the surface, it is recommended to apply adhesive to the reverse side of the tile as well before to put it on the surface covered with the mixture.

   A tile must be laid within 10 minute from application of adhesive on the basis. Correction of the tile position can be done within 10 minutes after the tile is laid. There is no need to soak tiles in water before use. The air temperature and the temperature of the basis must be from +5° to +30°.

   Grouting of wall tiles can be done in 6-8 hours, grouting of floor tiles in 24 hours. In bad conditions (strong wind, direct sunshine, high or low temperature, highly absorbing surface) lifetime of the prepared mixture may be decreased.

   When used for heated floor systems, the system should be switched off before to start tiling and can be switched on again after adhesion process is fully finished (28 days). All technical characteristics of the adhesive are fully active at the temperature of 18-20ªC and 60% humidity level.

 
Consultation on the pplication materials

MAXI PLUS

  

   Thick-layer tile adhesive IVSIL MAXI PLUS is based on cement, fractioned sand and special modifying additives. The main characteristic of this tile adhesive – «thick-layer» – speaks for itself. It is mostly used for ceramic tiles and ceramic-granite tiles of medium size. It can level small uneven patches of walls and floors (up to 20 mm).

   This material has been designed to materialise an idea of perfect multipurpose tile adhesive:

   - Its layer of application is from 2 to 20 mm;

   - It is used for any type of tiles and ceramic-granite (size 30*30);

   - It is suitable for work in any conditions and any type of basis;

   - It is suitable for heated floor setting;

   - It saves time and labour due to combining of technological operations.

   IVSIL MAXI PLUS elasticity allows it to sustain changes of temperature and dynamic vibrations of the surface. It can be used as floor tiling adhesive with ability to level floor surface because it does not shrink when setting. Besides tile adhesive IVSIL MAXI PLUS is adhesive with strong fixing ability.    

   Basic price of thick-layer tile adhesive is 185 roubles. See the prices of other tile adhesives in the section «Price List».

See also: thin professional adhesive for tiles and standard ceramic-granite IVSIL CLASSIC or go back to the section all IVSIL Tile adhesives.   

IVSIL dry mixes: adhesive for tiles and Standard ceramic-granite thick-layer IVSIL MAXI PLUS

 
 

Technical characteristics

Mixing proportion: 1l of water
On 1 kg of a mix0,19 0,21l
On 25 kg of a mix4,75 5,25l
Thickness of a layer of a solution, mm2 20
Viability of a solution3-4 hours
Open operating time15 min
Updating time10 min
Adhesive strength0,8 MPa
Frost resistance50 cycles
Packaging25 kg bag
Consumption on 1sq.m1,3 1,5kg
Firmness to temperaturesfrom +5 to +30
 
Packaging and storage
Adhesive mix Maxi Plus is delivered in 25kg Kraft-bags. A storage warranty period in a dry premise in packaging materials of the manufacturer 12 months.
The consumption
Average consumption 1,3 1,5 kg of a dry mix on 1 m. of a sq. surface at a thickness of a layer of a solution of 1 mm. Practically the expense depends on degree of flatness of the base, size of a teeth of a spatula and a sort of an applied tile.
 
Home Search and map
Rambler's Top100
Site development —
the Internet-agency «Webstroy»