TilingPlastering and renderingFloor levelingFinishingPrimersOther adhesivesWaterproofing and repairingTile GroutsUnmodified mixes
rus  |  eng
 

Base preparation

   The base surface should be strong, carefully cleared of dust, dirt, oils, and greases. Unstable and fragile parts of the base must be removed. Unevenness of a walls, a crack, and a recess should be pre-aligned with one the Plasters IVSIL. To fast correct uneven floors use self-leveling floor IVSIL EXPRESS-FINISH or screed IVSIL EXPRESS-BASIS (from line of materials "Quick repare").

   Before the faceworking surface should be primed with IVSIL BAZOVAYA. Strongly absorbing bases (gaze and foam concrete, gipsum plaster, anhydrite floor) should be primed with IVSIL GLUBOKOGO PRONIKNOVENIYA (primer penetrator).

Mixing of mortar

  Dry mix is poured into a mixing bucket with clean water in the following proportion: 1 kg of dry mix for 0,19 -0,21 l of water. Then it is thoroughly stirred, manually or with a mixing drill, until the mixture is homogeneous and elastic. The received mixture is left for 5 minutes and then stirred again. Prolonged period of this tile adhesive setting allows this mixture to be used within 30 min.

Application

   Adhesive solution is applied on basis with the help of a trowel and then is spread with a notched trowel. The size of notches depends on the size of a tile. Put a tile on the top of the mixture, which has just been applied, and press it to the surface. After being pressed, adhesive mixture should be covering not less than 65% of the tile’s surface, for ceramic tiles 20*20 and bigger and for all size ceramic-granite - 80%.

   When used for exterior jobs, to provide 100% of tile’s cover with adhesive and to guarantee gluing to the surface, it is recommended to apply adhesive to the reverse side of the tile as well before to put it on the surface covered with the mixture.

   A tile must be laid within 5-7 minute from application of adhesive on the basis. Correction of the tile position can be done within 5 minutes after the tile is laid. There is no need to soak tiles in water before use. The air temperature and the temperature of the basis must be from +5° to +30°. Grouting of wall tiles can be done in 6-8 hours, grouting of floor tiles in 24 hours. In bad conditions (strong wind, direct sunshine, high or low temperature, highly absorbing surface) lifetime of the prepared mixture may be decreased.

   When used for heated floor systems, the system should be switched off before to start tiling and can be switched on again after adhesion process is fully finished (28 days). All technical characteristics of the adhesive are fully active at the temperature of 18-20° and 60% humidity level.

 
Consultation on the pplication materials

EXPRESS+

  

   Rapidly setting tile adhesive IVSIL EXPRESS+ is based on cement bonding component. It contains fractioned sand and polymer additives. Tile adhesive Express plus is one of our products from IVSIL «Fast repair» range, it is designed for quick wall and floor tiling with ceramic and mosaic tiles of any size, ceramic-granite (size 30x30) and also natural stone tiles of middle size and artificial stone tiles.

   It is suitable for dry and wet conditions, for exterior and interior jobs. It can be applied to most of the concrete, cement and anhydrite basis. This adhesive can be used for heated flooring systems. It is characterised by short period of time for setting and drying.

   One can walk over the floor and start grouting in 3 hours after tilling, which is labour and cost effective. In combination with IVSIL floor levelling mix, from the range of «Fast repair» products, IVSIL EXPRESS+ guarantees fast concluding the whole process of tilling: starting from prime treatment of the basis and then floor levelling, tilling and grouting – all of it within 15-17 hours.

   This product is recommended for quick tilling of bathrooms, apartments, office premises and other places, where you need to perform tilling in short time. To read more about our «Fast repair» products click HERE. The basic price of rapidly setting tile adhesive for Moscow and Moscow region is 240 roubles/25 kg. To find prices of other IVSIL tile adhesives, please visit the section «Price list».

   See also:

   - fast drying floor levelling mix from «Fast repair» range IVSIL EXPRESS BASIS,

   - fast setting finish-off floor levelling mix IVSIL EXPRESS-FINISH for quick flooring or go to the section all IVSIL Tile adhesives.

   Dry construction IVSIL mixes: fast drying tile adhesive IVSIL EXPRESS+

 
 

Technical characteristics

Mixing proportion: 1l of water
On 1 kg of a mix0,19 0,21 l
On 25 kg of a mix4,75 5,25 l
The consumption at a thickness of a layer of 1 mm, on 1 sq. m1,3 1,5 kg
Thickness of a layer of a solution, mm2 - 6mm
Viability of a solution30 min
Open operating time5 - 7 min
Updating time5 min
Hardening time3 hours
Finish of seams3 hours
Temperature of works and the baseFrom +5 to +30
Adhesive strength0,7 MPa for ceramic tiles, 0,5 MPa for ceramic-granite
Frost resistance35 cycles
Packaging25 kg bag
 
Packaging and storage
Adhesive EXPRESS + is delivered in 25kg and 5 kg Kraft-bags. A storage warranty period in a dry premise in packaging materials of the manufacturer 6 months
The consumption
Average consumption 1,3 1,5 kg of a dry mix on 1 m. of a sq. surface at a thickness of a layer of a solution of 1 mm. Practically the expense depends on degree of flatness of the base, size of teeth of a spatula and a sort of an applied tile.
 
Home Search and map
Rambler's Top100
Site development —
the Internet-agency «Webstroy»