TilingPlastering and renderingFloor levelingFinishingPrimersOther adhesivesWaterproofing and repairingTile GroutsUnmodified mixes
rus  |  eng
 

Base preparation

   The base surface should be strong, carefully cleared of dust, dirt, oils, and greases. Unstable and fragile parts of the base must be removed. Small irregularities surface of furnace and fireplace (depth to 5mm) may be aligned using tile adhesive IVSIL TERMIX.

   Before the faceworking surface should be primed with IVSIL BAZOVAYA. Strongly absorbing bases (gaze and foam concrete, gipsum plaster, anhydrite floor) should be primed with IVSIL GLUBOKOGO PRONIKNOVENIYA (primer penetrator).

Mixing of mortar

   Dry mix is poured into a mixing bucket with clean water in the following proportion: 1 kg of dry mix for 0,20-0,23 l of water. Then it is thoroughly stirred, manually or with a mixing drill, until the mixture is homogeneous and elastic. The received mixture is left for 5 minutes and then stirred again. Prolonged period of this tile adhesive setting allows this mixture to be used within 4 hours.

Application

   Adhesive solution is applied on basis with the help of a trowel and then is spread with a notched trowel. The size of notches depends on the size of a tile. Put a tile on the top of the mixture, which has just been applied, and press it to the surface. After being pressed, adhesive mixture should be covering not less than 65% of the tile’s surface, for ceramic tiles 20*20 and bigger and for all size ceramic-granite - 80%. When used for exterior jobs, to provide 100% of tile’s cover with adhesive and to guarantee gluing to the surface, it is recommended to apply adhesive to the reverse side of the tile as well before to put it on the surface covered with the mixture.

   A tile must be laid within 10 minute from application of adhesive on the basis. Correction of the tile position can be done within 5 minutes after the tile is laid. There is no need to soak tiles in water before use. The air temperature and the temperature of the basis must be from +5° to +30°. Grouting of wall tiles can be done in 6-8 hours, grouting of floor tiles in 24 hours. In bad conditions (strong wind, direct sunshine, high or low temperature, highly absorbing surface) lifetime of the prepared mixture may be decreased.

   When used for heated floor systems, the system should be switched off before to start tiling and can be switched on again after adhesion process is fully finished (28 days). All technical characteristics of the adhesive are fully active at the temperature of 18-20° and 60% humidity level.

 
Consultation on the pplication materials

TERMIX

  

   Heat resistant tile adhesive for fireplaces and stoves IVSIL TERMIX is based of special aluminate cement and contains chemical additives. Strong TERMIX adhesive with high elasticity and strong bonding capacity is good not only for use as heat resistant adhesive for fireplaces, but is equally good for heated floors systems in hard conditions (for example heated floor on the balconies).

   Heat resistant adhesive can sustain changes of temperature on sunlit facade in sub-tropical climate zones of Russia or severe conditions of winter frosts in Siberia, in any place where tiled surface is subjected to changes of temperature (for example: tiled kitchen wall area next to the cooker).  

   New upgraded formula of heat resistant tile adhesive IVSIL TERMIX increased the range of sustainable temperature for tiles from -30ªC to 250ªC!!! Such characteristics of IVSIL TERMIX make it a perfect adhesive for heat resistant tilling. They also guarantee good final result of tilling, even if the technology of stove brickwork has not been properly observed and the walls of the stove are overheated in places. 

   Tile adhesive IVSIL TERMIX is also suitable for stove tiling with clinker tiles, ceramic-granite, natural and artificial stone. This adhesive can be used for tiles, ceramic-granite and stone over any basis, both in hard conditions and standard conditions on building façade, terrace and balcony flooring in any climatic conditions. It can be applied to most of solid surfaces, including plasters, concrete, brick (heat resistant bricks as well), cement, anhydrite walls and floors. See the price of adhesive for fireplaces and stoves in the section «Price List».

   See also: product group IVSIL Tile adhesives, IVSIL primer for interior and exterior jobs IVSIL BAZOVAYA.

   IVSIL products for fireplaces and stoves tilling: heat resistant tile adhesive IVSIL TERMIX, tile adhesive for heated floors.

 
 

Technical characteristics

Mixing proportion: 1l of water
On 1 kg of a mix0,20 0,23
On 25 kg of a mix5,0 5,75
The consumption at a thickness of a layer of 1 mm, on 1 sq. m1,5 1,6 kg
Thickness of a layer of a solution, mm2 6
Viability of a solution4 hours
Open operating time10 min
Updating time5 min
Finish of seams24 hours
Temperature of works and the baseFrom +5 to +30
Adhesive strengthnot less 0,9 MPa
Packaging25 kg bag
 
Packaging and storage
The dry adhesive mix is delivered in 25 kg Kraft-bags. A storage warranty period in a dry premise in packaging materials of the manufacturer is 6 months from the date of the manufacturing, specified in packing.
The consumption
Average consumption 1,5 1,6 kg of a dry mix on 1 m. of a sq. surface at a thickness of a layer of a solution of 1 mm. Practically the expense depends on degree of flatness of the base, size of teeth of a spatula and a sort of an applied tile.
 
Home Search and map
Rambler's Top100
Site development —
the Internet-agency «Webstroy»