TilingPlastering and renderingFloor levelingFinishingPrimersOther adhesivesWaterproofing and repairingTile GroutsUnmodified mixes
rus  |  eng
 

Base preparation

   The surface for facade plaster application must be solid, cleaned from dust, mud, oil, fats, lime, wax, chalk or lime mixtures, oil or emulsion paints. Prior to plastering, the basis must be treated with IVSIL BAZOVAYA (Basis) primer. Strongly absorbing bases (gaze and foam concrete, gipsum plaster, anhydrite) should be primed with IVSIL GLUBOKOGO PRONIKNOVENIYA (primer penetrator). Basis with different absorption level (brickwork of different materials) should be covered by reinforcing mesh before to apply plaster.

   If the curvature of the walls and there are deviations from the verticaevelling, levelling of walls is made with the help of installed markers.

Mixing of mortar

   Dry plaster mix is poured into a mixing bucket with clean water in proportion of 1 kg of dry mix per 0,13-0,15 l of water, then thoroughly stirred manually or with the help of mixing drill, until homogeneous, elastic mixture without any lumps or clots is received. The mixture is left for 5-10 minutes and then stirred again.

   If using a mechanized application method, pour dry mix into a machine and set up water feed according to the required consistence of mixture.

   Prepared facade plaster mixture should be used within 2 hours.

Application

   Ready plaster mixture is applied with the help of plaster trowel to the surface in a layer of 5 to 20 mm and initially levelled and squared with a stick. If necessary, levelling can be done in two layers. In this case the first layer of plaster should be roughed (“combed” with a plastering comb in the form of a swallow tail) and then let to dry for 2-3 days.

 
Consultation on the pplication materials

GROSS

  

   Cement based plaster IVSIL GROSS: extra strong cement based facade plaster with big sand fractions and a set of polymer additives.

Facade cement plaster for levelling walls made of concrete, aerated concrete, bricks or stone inside and outside surfaces. This plaster suitable for manual and machine application. Facade plaster IVSIL GROSS is easy to apply, to float and to level to a layer up to 40 mm in one go, it does not crack whilst drying and has sufficient elasticity.

   The adhesion level of this plaster is higher than average, which makes this plaster IVSIL GROSS reliable and long lasting material for facade treatment even in difficult climatic conditions, in areas with big temperature changes and multiple precipitations. It is an excellent material for exterior use in Southern regions where it can be successfully used on exposed to the sun facade. Cement based plaster mix IVSIL GROSS is also reliable when used for levelling of facade walls in climatic conditions of Russia.

   Due to high level of strength IVSIL GROSS plaster is very good for plastering of lower parts of facade walls, for office premises, entrance halls and staircases, walls of premises which are subjected to high possibility of damage (shopping centres, supermarkets, building corridors).

   The basic price of facade plaster IVSIL GROSS is 155 roubles/25 kg. To find the information about prices of other IVSIL facade plasters please visit the section «Price list».

   See also: thin cement facade plaster IVSIL THINER, cement putty for finish-off levelling IVSIL FASADNAYA (FACADE), exterior use primer IVSIL BAZOVAYA (Basic) or go to all IVSIL Plasters.

   Dry IVSIL plaster mixes: strong cement based facade plaster for manual and machine application IVSIL GROSS, sand-cement plaster for repair, sand-cement plaster for facade jobs.

   Please, be aware that:

   Every winter, till the end of cold season, IVSIL GROSS winter version is available. It frost resistant and it allows to do plastering at subzero temperatures. Whilst ordering winter version of plaster just add the word «winter» to the name of the plaster! The basic price for cement plaster IVSIL GROSS winter version is 210 roubles.

 
 

Technical characteristics

Mixing proportion: 1l of water
On 1 kg of a mix0,13 0,15 l
On 25 kg of a mix3,25 3,75 l
The consumption at a thickness of a layer of 1 mm, on 1 sq. m1,7 2,0 kg
Thickness of a layer of a solution, mm10 40 mm
Viability of a solution2 hours
Hardening time2 3 days
Achievement of full durability28 days
Temperature of works and the baseFrom +5 to +30
Durability on compression15 MPa
Adhesive strength1 MPa
Frost resistance35 cycles
Packaging25 kg
Mobility of mortar mixes8 10 cm
Colorgrey
 
Packaging and storage
The dry mix is delivered in kraft-bags of 25 kg. A storage warranty period is 6 months from the date of the manufacturing.
The consumption
The average expense 17-20 kg of a dry mix on 1 m. of a sq. surface at a thickness of a layer 10 mm. The exact expense depends on degree of flatness (relief) of the basis.
 
Home Search and map
Rambler's Top100
Site development —
the Internet-agency «Webstroy»