TilingPlastering and renderingFloor levelingFinishingPrimersOther adhesivesWaterproofing and repairingTile GroutsUnmodified mixes
rus  |  eng
 

Base preparation

   The surface for plaster application must be solid, cleaned from dust, mud, oil, fats, lime, wax, chalk or lime mixtures, oil or emulsion paints. Prior to plastering, the basis and board joints must be treated with IVSIL OSNOVA primer. 

   Strongly absorbing bases (gaze and foam concrete, gipsum plaster, anhydrite) should be primed with IVSIL GLUBOKOGO PRONIKNOVENIYA (primer penetrator) and pre-aligned by one of repairing plasters IVSIL.

   Unevenness of a walls, a crack, and a recess should be also pre-aligned.

Mixing of mortar

   Dry mix is poured into a mixing bucket with clean water in proportion of 20 kg of dry mix per 6 - 6,5 l of water, then thoroughly stirred manually or with the help of mixing drill for approx. 1 minute, until homogeneous, elastic mixture without any lumps or clots is received. The mixture is left for 5-10 minutes and then stirred again.

   Prepared mix should be used within 1 hour.

Application

   levelling up: Ready mixture is applied on prepared surface with a metal trowel to form a layer of 0,5 to 8 mm. A small steel trowel (30 cm) is used for partial levelling, and a two-handed trowel for whole levelling. 

   If necessary, several layers can be applied, providing every previous layer has already dried (in 24 hours). The basis and air temperature should be +5ºC to +30ºC. Dried layer should be polished with a fine abrasive material.

   Joint filling: The ready solution is applied in the joint so that it fills the niche. Joint band is pressed to Joint Filler with a broad steel spatula. Joint filler is then applied on top of the joint band so that it fills the joint. Finally Joint Filler is levelled to the level of the boards with a wide steel spatula. After drying the joint are finished with thin abrasive material (sand paper).

 
Consultation on the pplication materials

FINISHNAYA

  

   White gypsum-based IVSIL FINISHNAYA finishing putty for indoor walls and ceilings in dry conditions is made of high-quality gypsum with mineral filler and polymer additives. This thin gypsum putty is suitable for high quality finishing-off levelling of walls and ceilings made of concrete, bricks, plastered surfaces prior to further application of any type of paint or wall paper.

   It is recommended for fine finishing treatment of walls and ceilings in heated premises, for finishing-off surfaces of gypsum and cement plasters and for application to plasterboards on walls and ceilings of apartments, houses, hotels.

   Finishing gypsum filler is also used for treatment of plasterboard, and gypsum-fibre board and drywall joints.

   This putty is easy to apply, has high level of adhesion and strength. It does not crack whilst drying, forms smooth even surface. 

   In Moscow retail price of gypsum IVSIL FINISH putty is 230-245 roubles/20 kg. Prices of other IVSIL putty mixes can be found in the section Price List.

   See also: white finish polymer coating IVSIL GREENTEX, gypsum plaster IVSIL RUST or go back to the section Finishing. At that page you can also watch video about technological process of plasterboard joints treatment with the help of finishing putty (comments and texts are in Russian).

   IVSIL dry finishing mixes: white gypsum based finishing plaster for walls and ceilings IVSIL FINISHNAYA («Finish»), filler for jointing boards, thin plaster for plasterboard joints treatment.

 
 

Technical characteristics

Mixing proportion: 1l of water
On 1 kg of a mix0,40,5
On 25 kg of a mix6,07,5
The consumption at a thickness of a layer of 1 mm, on 1 sq. m0,91kg
Viability of a solution60 mines
Packaging15 kg
 
 
Home Search and map
Rambler's Top100
Site development —
the Internet-agency «Webstroy»